RAID rebuild times determine how long a large surveillance array runs in a degraded, unprotected state, and on multi-terabyte volumes a rebuild can take many hours or even days. During that window, a second drive failure can cause data loss and recording performance can suffer. Rebuild time is driven by drive capacity, RAID level, controller performance and live recording load, which is why it matters for any IP CCTV camera system storing footage at scale. The sections below explain what controls rebuild speed, the risks involved and how to manage them.
What determines how long a RAID rebuild takes?
RAID rebuild time is determined mainly by the capacity of the failed drive, the speed at which the controller can read the surviving drives and write to the replacement, and how much other work the array is doing. Larger drives and wider arrays take longer to rebuild.
The main factors are:
- Drive capacity: every sector on the replacement drive must be reconstructed, so a 20TB drive takes far longer than a 4TB drive, regardless of how much of it was actually in use.
- RAID level: parity-based levels such as RAID 5 and RAID 6 must read data from every surviving drive in the group to recalculate the missing data. Mirrored layouts only need to copy from a single partner drive.
- Array width: the more drives in a parity group, the more data must be read and processed per rebuilt block.
- Controller capability: hardware RAID controllers with dedicated processing and battery-backed cache handle parity calculations more efficiently than software-based approaches.
- Rebuild priority settings: most controllers let administrators balance rebuild speed against foreground workload.
- Drive sustained throughput: rebuilds are largely sequential operations, so the sustained read and write speed of the drives sets a practical ceiling.
As a simple, hypothetical illustration, a drive that sustains 200MB/s would need roughly 28 hours to write 20TB even if nothing else were happening. Real rebuilds are almost always slower than this theoretical minimum, and the figure is an estimate rather than a performance guarantee.
Why are rebuilds slower on live surveillance arrays?
Rebuilds are slower on live surveillance arrays because the array must keep writing continuous video streams while it reconstructs the failed drive. Recording is a constant, non-negotiable write load, so the controller can only dedicate spare capacity to the rebuild, which stretches the process considerably compared with an idle array.
Several characteristics of surveillance workloads compound this:
- Continuous 24/7 writes: unlike a typical business server, there are no quiet overnight periods in which the rebuild can run at full speed.
- Concurrent playback and export: operators reviewing incidents, running investigations or exporting evidence add read demand on the same disks.
- Analytics and metadata: where analytics generate metadata alongside video, additional I/O competes with the rebuild.
- Degraded performance during rebuild: with a drive missing, every read from the affected group requires reconstruction, reducing headroom for recording.
This is why arrays that are comfortably sized for normal operation can become marginal during a rebuild. Sizing a recording server only for steady state, without leaving throughput headroom for a degraded and rebuilding condition, is a common design mistake. Secure Logiq’s guidance on selecting a server is a useful starting point for working out that headroom.
What risks does a long rebuild create for recorded footage?
A long rebuild extends the period in which the array has reduced or no redundancy, increasing the chance that a further drive failure, read error or controller fault causes lost recordings. It can also reduce recording headroom, raising the risk of dropped frames in the CCTV software layer.
The main risks are:
- Second drive failure: in RAID 5, a failure during rebuild means the volume is lost. RAID 6 tolerates a second failure, but is still exposed if a third drive fails.
- Unrecoverable read errors: rebuilding requires reading every sector of the surviving drives. A latent read error on a drive that has previously appeared healthy can cause the rebuild to fail or leave gaps in the data.
- Correlated drive stress: drives from the same batch with similar operating hours are placed under heavy, sustained read load at exactly the moment they are least able to be replaced.
- Recording performance impact: if the array cannot sustain both recording and rebuild, the VMS may report dropped frames or gaps in recordings.
- Longer exposure window: the longer the rebuild, the longer the site depends on a single layer of protection.
It is important to remember that RAID is not a backup. It protects against drive failure, not against deletion, corruption, controller faults or site-level events. For critical sites, a rebuild-related loss of footage may also have compliance and evidential consequences, so the design should assume that rebuilds will happen and plan for them.
Which RAID level is best for large surveillance arrays?
For large surveillance arrays, RAID 6 or RAID 60 is generally the safer choice because they tolerate two simultaneous drive failures per group. RAID 5 is increasingly risky on high-capacity drives because of the long rebuild window, though it can remain suitable for smaller or lower-risk deployments.
The trade-offs can be summarised as follows:
- RAID 5: single parity, efficient use of capacity, but vulnerable to a second failure or read error during a long rebuild.
- RAID 6: dual parity, higher protection during rebuilds, at the cost of some usable capacity and additional parity overhead.
- RAID 60: multiple RAID 6 groups striped together. Each group rebuilds independently, so rebuilds involve fewer drives and can be shorter, while the array scales to high capacities.
- RAID 10: mirrored pairs striped together, with the fastest and simplest rebuilds, but the least efficient capacity use, which is rarely attractive for very large video retention requirements.
Secure Logiq enterprise servers use hardware-accelerated, battery-backed RAID arrays, typically RAID 5, 6 or 60, with hot-swappable spares configured as standard. The operating system sits separately on dual enterprise SSDs in hardware RAID 1, so a recording array rebuild does not affect the system drive. The best choice depends on retention requirements, risk tolerance and the criticality of the site, and is best decided at design stage.
How can rebuild times be reduced or managed?
Rebuild times can be reduced by using hot spares, splitting capacity into multiple smaller RAID groups, choosing appropriately sized drives and ensuring the controller has enough performance headroom. Because they cannot be eliminated, they should also be managed through proactive monitoring and sensible design margins.
Practical measures include:
- Configure hot spares: a hot spare starts rebuilding automatically on failure, removing the delay of waiting for someone to attend site and swap the drive.
- Use smaller parity groups: RAID 60 or similar designs limit how many drives are involved in each rebuild.
- Use surveillance-grade drives: drives designed for 24/7 operation and sustained sequential workloads are better suited to long rebuild stress.
- Leave throughput headroom: size the array for recording plus rebuild, not recording alone. Tools such as the Logiqal Benchmark utility can help validate server and storage throughput before deployment.
- Monitor drive health: proactive alerts on SMART data, reallocated sectors and media errors allow drives to be replaced before they fail.
- Tune rebuild priority carefully: a higher rebuild priority shortens exposure but may affect recording, so settings should reflect site priorities.
- Maintain a hardware warranty and replacement process: fast replacement of failed drives shortens the time spent degraded.
Software-defined approaches can also help. Secure Logiq’s Logiqal Video Volume is designed for high-throughput sequential video workloads and separates video data from metadata streams to reduce fragmentation and improve archive stability, which supports healthier drives over time. More detail is available in the Logiqal Core Architecture announcement.
When should an array be split into smaller volumes?
An array should be split into smaller volumes when a single large group would produce rebuild times that the site cannot safely tolerate, or when a single failure domain would affect too many cameras. Splitting limits the number of drives involved in each rebuild and reduces the footage at risk.
Consider splitting when:
- High-capacity drives in a wide parity group push rebuilds into multiple days.
- The deployment is mission-critical, such as transport hubs, stadiums or critical infrastructure, where gaps in recordings are unacceptable.
- Recording load is already close to the array’s sustained write limit, leaving little headroom for rebuilds.
- Different camera groups have different retention or priority requirements.
- Multiple recording servers or storage nodes can share the load, so that one degraded volume affects only part of the system.
The trade-off is some loss of usable capacity and slightly more management overhead, as each group carries its own parity. For large estates, the extra resilience is usually worth it, and a well-planned design will balance this against rack space, power and cost. A system design review can model these trade-offs against your camera count, bitrates and retention targets, and the Qatar University SAN storage case study shows how storage architecture decisions play out on a large site.
If you are planning or upgrading a large surveillance storage array and want rebuild behaviour considered at design stage, you can speak to Secure Logiq’s engineers about your retention, throughput and resilience requirements.
Frequently Asked Questions
How do I estimate the rebuild time for my own surveillance array before a drive fails?
Start with a baseline by dividing the replacement drive’s capacity by its sustained write speed, then add a realistic margin for live recording load. For a more accurate picture, run a controlled test during commissioning: tools such as the Logiqal Benchmark utility can validate throughput, and many RAID controllers let you simulate or schedule a rebuild on a spare drive. Treat the result as an estimate, and expect real-world rebuilds to take noticeably longer than the theoretical minimum.
What should I do immediately when a drive fails in a live recording array?
First confirm the array status in the controller or RAID management utility and check whether a hot spare has already started rebuilding. If not, replace the failed drive with an identical or compatible model as quickly as possible and avoid power-cycling the server. Then reduce non-essential load, such as large exports or heavy playback, check the other drives’ SMART health, and verify in your VMS that there are no dropped frames or recording gaps.
Should I increase rebuild priority to finish faster, or keep it low to protect recording?
It depends on the site’s priorities and the headroom available. A higher rebuild priority shortens the window of reduced redundancy but can cause dropped frames if the array is already near its write limit, while a low priority protects recording at the cost of a longer exposure period. A sensible approach is to test a medium setting during commissioning, monitor recording health, and only raise priority if the VMS shows stable ingest.
Is it safe to keep using RAID 5 on an existing system with large drives?
It can be acceptable for smaller or lower-risk sites, but the risk rises with drive capacity and array width because rebuilds take longer and a single read error can be fatal. If you are staying with RAID 5, make sure you have hot spares, proactive SMART monitoring, recent verified backups of critical footage, and a fast drive replacement process. For critical or high-capacity deployments, plan a migration to RAID 6 or RAID 60 at the next hardware refresh.
How can I spot a failing drive before it triggers a rebuild?
Enable alerts for SMART attributes such as reallocated sectors, pending sectors, and media or read errors, and review the controller’s event log regularly. Run scheduled patrol reads or consistency checks so latent bad sectors are found and repaired while the array is still healthy. Replacing drives that show rising error counts, rather than waiting for a hard failure, avoids rebuilding under pressure.
Does using a hot spare really make that much difference?
Yes, because it removes the delay between failure and the start of the rebuild, which on remote or unattended sites could otherwise be hours or days. The rebuild starts automatically, so the exposure window is limited to the rebuild itself rather than the rebuild plus response time. Remember to replace the failed drive and re-establish a hot spare afterwards so the next failure is also covered.
Can I rely on RAID alone to protect critical or evidential footage?
No, RAID only protects against drive failure and does not cover deletion, corruption, controller faults or site-level events like fire or theft. For critical or evidential footage, combine RAID with a separate protection layer such as secondary storage, replication to another server or site, or export of key incidents to protected archive storage. Define this in the design stage alongside retention and compliance requirements.
Related Articles
- What role do SAN switches play in a large CCTV system?
- What should be included in a SAN storage specification for enterprise CCTV?
- Can a standard IT server handle HD surveillance workloads?
- What is the role of a surveillance server in an enterprise VMS?
- Why is redundant power supply important in a surveillance server?